Waterpik Technologies Plumbing Product JP 120 User Manual

COMBO SYSTEM INSTALLATION INSTRUCTIONS  
CARE AND CLEANING  
1) Remove old showerhead from shower arm. Clean shower arm pipe threads thoroughly.  
Polish with moist, soft cloth. For heavier cleaning, submerge in household vinegar. If  
other cleansers contact product, rinse immediately.  
2) Attach diverter valve by threading clockwise onto shower arm with diverter bracket  
facing right.  
3) Attach wall mount showerhead to front-facing end of diverter.  
2 In 1 Shower System  
NOTE  
Vacuum Breaker  
4) Attach one end of the hose to hand shower and the other end to the bottom of the  
diverter.  
Sistema de ducha 2 en 1  
The state of Wisconsin and the City and County of Los Angeles, California, U.S.A.  
require vacuum breakers on all hand-held showerheads. Vacuum breakers are required  
by certain plumbing codes in order to protect water supplies from potential back-flow.  
5) Point all showerheads away from you and turn on the water full force. Check for leaks.  
Re-tighten all attachments if necessary.  
Installation  
OPERATION  
The vacuum breaker is located on the end of the hose. Hand tighten the vacuum breaker  
clockwise onto the bracket. DO NOT ATTACH VACUUM BREAKER TO SHOWERHEAD.  
This would stop the flow of water.  
1) Spray pattern is controlled by outside trim ring.  
2) To change between the hand-held or  
fixed mount spray, turn the tabs on  
the diverter clockwise or counter  
clockwise.  
Instruction Manual  
Manual de Instrucciones  
LIMITED LIFETIME WARRANTY  
Water Pik, Inc. warrants to the original purchaser of this product that it is free from  
defects in material and workmanship for as long as the original purchaser owns this  
product. Water Pik will replace any part of the product, which in our opinion is defective,  
provided that the product has not been abused, misused, altered or damaged after  
purchase. (This includes damage due to use of tools or harsh chemicals). In the event an  
item has been discontinued, we will replace with what we deem to be the closest product.  
Water Pik is not responsible for labor charges, installation, or other consequential cost.  
The responsibility of Water Pik shall not exceed the original purchase price of the product.  
Models:  
JP-120 and NML-659 Combo  
TRS-523 and TRS-553 Combo  
Modelos:  
JP-120 y NML-659 Combinado  
TRS-523 y TRS-223 Combinado  
Actual product may not match that shown.  
This warranty gives you specific legal rights. You may also have other rights that vary  
where you reside. Save your receipt, as proof of purchase is required for warranty action.  
El producto real puede ser diferente del  
modelo que se muestra.  
COMPONENTS  
Your showerhead comes with the respective  
hardware set shown below.  
TROUBLESHOOTING GUIDE  
Have questions or need assistance?  
or call for Customer Service at  
1-800-525-2774  
8:00 a.m. to 4:00 p.m.,  
Mountain Standard Time, Monday-Friday  
Problem  
Solution  
No water flow from installed a Confirm previous shower washer is not in the  
Waterpik® brand showerheads are equipped with an  
OptiFlow® regulator that limits maximum water  
flow to 2.5 gallons per minute at 80 psi as  
mandated by U.S. federal law.  
shower head:  
j-pipe.  
b Confirm the hose is properly installed, try  
switching ends.  
Water Pik, Inc.  
1730 East Prospect Road  
Fort Collins, CO 80553-0001  
c Confirm there is only one washer in the pivot  
ball.  
Low water pressure or  
missing spray patterns  
a Clean shower head in vinegar/water solution.  
(See care section).  
FN 20009959-F AC  
Waterpik® (stylized) is a trademark of Water Pik, Inc. registered in the EU, Switzerland,  
Mexico, Canada, and United States.  
Waterpik® is a trademark of Water Pik, Inc. registered in Argentina, Australia, Austria,  
Canada, China, Czech Republic, Hungary, India, Japan, Poland, Russian Federation,  
South Africa, Switzerland, Ukraine, and the United States.  
OptiFlow® is a trademark of Water Pik, Inc. registered in Australia, Canada, the EU,  
Korea and the United States.  
b Clean screen and flow regulator.  
Leaking at pipe pivot ball  
connection:  
a Confirm one single washer is seated on top of  
the screen.  
Flow regulator  
b Grate bar of soap across the j-pipe threads to  
act as a sealant.  
Hand-held bracket  
Diverter  
Showerhead and/or bracket a Immerse pivot ball and large nut of the bracket  
Filter screen  
Flow regulator  
stiff to change angle  
in hot water or use a blow dryer for several  
minutes and then use a towel to loosen the  
large nut.  
© 2010 Water Pik, Inc. Printed in China. Made in China.  
Vacuum breaker  
(some models)  
For Fixed Mount: install FM shower head to  
provide additional leverage to change angle of  
spray. (Contact Waterpik for further assistance).  
DATE: 21 May 2010  
CLIENT: Water Pik, Inc.  
FILENAME: FN20009959-FAC_ComboInst.indd  
FILE TYPE: Adobe InDesign CS4  
SIZE FLAT: 11” x 8.5”  
DESCRIPTION: 2 in 1 Shower System Instruction Manual  
PREPARED BY: Brian Colon  
SIZE FOLDED: 3.6875” x 4.25”  
INK: Black  
FORM: 20009959-F AC  
FOLDS: Indicated.  
DIELINE: N/A  
 
NOTES:  

Thomas Betts Furnace RGM 405 User Manual
Thule Automobile Accessories Kit 2041 User Manual
Topcom Cordless Telephone OG R400 User Manual
Top Innovations Iron SP 660 User Manual
Toshiba DVD Player SD K625 User Manual
Tripp Lite Network Card B130 101 User Manual
Tyco Computer Monitor 1847L Series User Manual
Viking Cooktop F20111C User Manual
VocoPro Karaoke Machine DVG 909K User Manual
VTech Telephone DS4121 3 User Manual